How to Remove Calcium Buildup in FaucetsShower Heads?

Calcium buildup in faucets and shower heads can cause damage to your plumbing system. How to remove calcium buildup in faucets and showers?

Faucets and showerheads are prone to clogging because they are located close to pipes or water supply lines. The problem is caused by minerals like lime scale that form inside them over time. When these minerals get stuck in the valves, faucets and showerheads stop working properly. If left untreated, calcium build up could cause serious problems such as leaks, burst pipes, and other costly repairs. A simple solution exists if you know what causes calcium build up and where to look.

How does calcium buildup occur?

Calcium build-up occurs when there is a high concentration of dissolved calcium ions in the water. This happens when hard water is used for drinking water or washing dishes. Hard water contains higher concentrations of calcium than soft water. It’s important to understand why this happens so we can prevent it from happening again.

Causes of calcium build-up

The first step in removing calcium build-up is understanding how it forms. There are two main reasons why calcium builds up:

Hard water has more dissolved calcium than soft water.

Water flows through pipes that have been exposed to hard water for an extended period of time.

If either of these conditions exist, then calcium will be deposited on the inner walls of pipes. Over time, calcium deposits will begin to accumulate.

If you use hard water for drinking water or washing clothes, then you should make sure that your water supply line is not exposed to hard water. You can do this by installing filters before the water reaches your home. Also, install a filter after the water leaves your house.

How to remove calcium build-up in faucets/shower heads?

There are several ways to remove calcium build-ups from your faucets and showerhead. They include using a non-scratching brush, vinegar, baking soda, and salt. Here are some tips on how to clean calcium build-up out of your faucets and showers:

Use a non-scratching brush

A non-scratching bristle brush is ideal for cleaning calcium build-up off of faucet and showerheads. Use a toothbrush with long bristles. Make sure to hold the brush at a 45 degree angle while brushing.


Vinegar is effective in dissolving calcium build-up. To use vinegar, fill a spray bottle with warm water and add one part white distilled vinegar to three parts water. Spray the mixture onto the area where calcium build-up is present. Let the vinegar sit for five minutes. Then rinse thoroughly with hot water. Repeat until all traces of calcium have disappeared.

Baking Soda

Baking soda works well for dissolving calcium build-ups. Mix equal amounts of baking soda and water. Pour the mixture into a spray bottle and spray onto the affected areas. Wait for about 10 minutes. Rinse with hot water. Repeat the process until calcium build-up disappears.


You can also dissolve calcium build-up with salt. Dissolve 1 teaspoon of table salt per gallon of water. Add the mixture to the affected area and let it sit overnight. In the morning, rinse with hot water. Repeat this process until calcium build-ups disappear.

How to prevent calcium build-up?

Calcium build up in water pipes may be caused by lime scale build-up from hard water, which usually occurs in areas where water is treated with chemicals such as chlorine for disinfection purposes. This causes the minerals calcium and magnesium to precipitate out of solution in the form of crystals. These crystals then clog water flow and cause frequent plumbing issues. The best way to prevent these problems is to use a softening agent in the shower head and faucet. There are two common types of softening agents available: those made for household use (e.g., vinegar or lemon juice) and those specially formulated for cleaning purposes. Some brands of shower heads include built-in softeners while others require a separate device to place into the showerhead.

What are the symptoms of calcium build-up?

When calcium build-up begins to occur, it usually starts to show its effects within six months. Symptoms include slow water flow, low pressure, discolored water, and even pipe bursts. As calcium levels increase, the amount of time required to flush toilets also increases. If you notice any of these signs, contact your local plumber immediately.

What will dissolve calcium deposits?

The most popular method used to dissolve calcium deposits is vinegar. Vinegar has been proven to work effectively because it contains acetic acid, which breaks down calcium carbonate into soluble calcium acetate. It’s important to note that vinegar cannot be used on copper piping. You should only use vinegar on plastic piping.

Other methods include using baking soda, salt, and lemon juice. Baking soda is an inexpensive option that can be used on both metal and plastic piping. Lemon juice is another good choice since it contains citric acid, which helps break down calcium deposits. Salt is another option if you want to try something different.

Why are vinegar baths effective?

Vinegar baths work because they help remove calcium deposits from inside the pipes. When you take a bath, you immerse yourself in a large container filled with water. Since the water is at room temperature, it doesn’t heat up quickly. Therefore, it takes longer to get warm enough to create steam. Steam is what removes calcium deposits. Because vinegar baths are so effective, many people choose to bathe daily to keep their pipes clean.


If you have noticed any of the above mentioned symptoms, it’s time to call a professional plumber. They will be able to determine the source of the problem and provide the proper treatment. Remember, if there is no visible damage, don’t worry about it. Just make sure to schedule regular maintenance visits to ensure that your home stays safe and healthy.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *