Water heater pilot wont stay lit do this

Water heaters are essential appliances in every home. They provide hot water to wash dishes, clean clothes, or even take a shower. In addition to providing hot water, they also save energy, reduce carbon emissions, and improve indoor air quality.

There are two types of water heaters: electric and gas. Electric water heaters run off electricity from the power grid. Gas water heaters burn natural gas.

Pilot valves are installed in the main line of the water supply pipe. When the temperature reaches a certain level, the pilot valve opens and allows cold water into the system. This helps to prevent damage to pipes and appliances.

Are you looking for ways to save money? If yes, then you should definitely consider installing a water heater pilot light. In this article, I’ll show you how to install a pilot light in a gas water heater.

Gas water heaters are very common appliances found in homes throughout the United States. They provide hot water to households, especially during cold seasons. However, they also require regular maintenance. One of the most important things to check is whether or not the pilot light is working properly.

When the pilot light does not work, you might experience some issues such as having cold showers, no hot water, and even carbon monoxide poisoning. The good thing is that you can easily fix it. All you need to do is follow these steps.

Water Heater Pilot Won’t Stay Lit? Do This

1. Turn Off the Power Supply

Turning off the power supply will stop all electrical devices from functioning. You have to turn off the power before you start any repair process.

2. Open the Drain Valve

Open the drain valve by unscrewing its cap.

3. Remove the Thermostat Cover

You can remove the thermostat cover with your hands.

4. Unscrew the Pilot Light Socket

Unscrew the socket by using a screwdriver.

5. Disconnect the Wires From the Pilot Light

Disconnect the wires connected to the pilot light by pulling them out.

Water Heater Pilot Light Will Not Light Up – Otosection

6. Replace the Pilot Light

Replace the old pilot light with a new one.

7. Close the Drain Valve

Close the drain valve after replacing the pilot light.

8. Reinstall the Thermostat Cover and Screw It Back On

Install the thermostat cover back on the unit. Then, screw it back onto the unit.

9. Check if the Pilot Light Is Working Properly

If the pilot light is still not lit, repeat the previous step until it lights up again.

10. Test the Heat Output

Test the heat output by turning on the tap at the bottom of the tank.

I

Why does my water heater pilot light keep turning off?

The first thing that comes to mind when we think about water heaters is the fact that they’re used to heat water. But what people don’t realize is that the pilot light actually serves another purpose too. It’s responsible for keeping the water flowing through the pipes.

The pilot light works by burning fuel. As soon as the water gets heated, the flame burns away and stops the flow of water. So, if the pilot light doesn’t light up, the water won’t be able to flow through the pipes.

How to Install a Water Heater Pilot Light?

Installing a water heater pilot light is easy. Follow these simple steps:

Step 1: Turn Off the Power Supply First, turn off the power supply by flipping the switch located near the outlet.

Step 2: Open the Drain Valve Next, open the drain valve by unscrewing its cap.

Step 3: Remove the Thermostat Covers Next, remove the thermostat covers by removing their screws.

Step 4: Unscrew the Pilot Lightsocket Next, unscrew the socket by using an appropriate tool.

Step 5: Disconnect the Wires Connected To the Pilot Light Next, disconnect the wires connected to the socket by pulling them out. Make sure to leave the wire attached to the thermostat intact.

Step 6: Replace the Pilot Light With a New One Next, replace the old pilot light with the new one.

Step 7: Close the Drain Valve Finally, close the drain valve after replacing it with the new one. Don’t forget to tighten it properly.

Step 8: Test the Heat Output If the pilot light isn’t working, check the heat output by turning the tap at the bottom.

Why Does My Water Heater Not Work?

If the water heater is not working, there are many reasons why this might happen. The most common reason behind this problem is the lack of gas or electricity in the area where the water heater is installed. Another possible cause could be a faulty connection between the hot and cold lines. In addition, you may have forgotten to install the thermostat cover.

How to Fix a Faulty Water Heater?

In case your water heater is not working due to any of the above-mentioned issues, follow these tips to fix the problem:

1. Check if Gas Or Electricity Is Available Where You Live

First, make sure that gas or electricity is available in the area where you live. If the power supply is turned off, you can use a flashlight to look for the gas line. If you see the pipe, then you know that the power supply is turned on.

2. Inspect the Connection Between the Hot And Cold Lines

Next, inspect the connection between the hot and the cold lines. If you find anything wrong, contact the plumber who installed the system.

5 Reasons Why Your Water Heater Pilot Light Won't Stay Lit (and How to Fix)

3. Check Whether There Are Any Leaks Inside the Tank

Finally, check whether there are any leaks inside the tank. If you notice any leak, call the plumber immediately.

4. Clean the Filter Regularly

Finally, clean the filter regularly. This will help keep the water clean.

5. Change the Filters Every Six Months

Change the filters every six months. It’s recommended to change the filters once a month.

What do you do if your pilot light won’t stay lit?

The first thing you should do is turn off the power supply. Then, you need to open the drain valve. After opening the drain valve, you need to remove the thermostat cover from the pilot light.

Once you’ve removed the thermostat cover, you need to unscrew the socket. Now, you need to disconnect the wires connected to it. Finally, you need to replace the old pilot light.

Conclusion

The water heater is an important part of our life. However, sometimes we need some help from professionals to repair it. We hope the information provided here helps you understand how to fix a faulty water heater.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *